Lantronix MSS Instrukcja Użytkownika Strona 11
- Strona / 91
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Command Reference Backward
2-2
2.1 Backward
Moves the user to the previous session when entered in Local mode.
See Also
Change Backward Switch, page 2-14; Show Session, page 2-66.
2.2 Change 80211
Note:
The Change 80211 Reset command must be entered after any 802.11
configuration command is issued. The changes made by the configuration
commands will not take effect until after the Reset command is used. The Change
802.11 Enabled/Disabled command requires a reboot before the change will
take effect.
2.2.1 Change 80211 Enabled
When 802.11 is enabled, the MSS checks for a compatible 802.11 wireless Ethernet PC card at startup and,
if one is present, uses the card instead of a wired Ethernet port. If no valid PC card is detected at startup, the
MSS uses the 10/100BASE-T (or, for the MSS4, the 100BASE-FX) network connection.
When 802.11 is disabled, the MSS will ignore an installed 802.11 card and will only look for a compatible
wired Ethernet connection.
You must reboot the MSS before those changes will take place.
Restrictions
Requires privileged user status.
Only applies to the MSS-VIA and certain MSS4 models. For the MSS4, only
one 802.11 card can be installed at a time. The card can be installed in either
slot of the MSS4.
Parameters
Enabled
Prompts the MSS to check for a compatible 802.11 wireless Ethernet
networking PC card at startup. If one is present, wireless networking will be
used instead of the wired Ethernet connection. You must reboot the MSS after
entering this command.
Disabled
Prompts the MSS to only look for a compatible 10/100BASE-T (or, for the
MSS4, the 100BASE-FX) wired Ethernet connection at startup. You must
reboot the MSS after entering this command.
BACKWARD
CHANGE 80211
ENABLED
DISABLED
- MSS Reference Manual 1
- Contents 3
- 1: Introduction 7
- 1.3 Command Line Editing 8
- 1.4 Help 9
- 1.5 About This Manual 9
- 2: Command Reference 10
- 2.1 Backward 11
- 2.2 Change 80211 11
- 2.2.2 Change 80211 Antenna 12
- 2.2.3 Change 80211 Channel 13
- 2.2.4 Change 80211 ESSID 13
- Infrastructure 15
- 2.2.9 Change 80211 Region 16
- 2.2.8 Change 80211 Power 16
- 2.2.10 Change 80211 Reset 17
- 2.2.11 Change 80211 RTS 17
- 2.2.12 Change 80211 WEP 18
- 2.3 Change Access 19
- 2.4 Change Autobaud 20
- 2.5 Change Autostart 21
- 2.6 Change Backward Switch 23
- 2.7 Change Bootgateway 23
- 2.8 Change BOOTP 24
- 2.9 Change Break 24
- 2.10 Change Buffering 25
- 2.11 Change Charsize 25
- 2.12 Change Datasend 26
- 2.13 Change Dedicated 28
- 2.14 Change DHCP 30
- 2.15 Change Domain 30
- 2.16 Change DSRLogout 31
- 2.17 Change DTRWait 31
- 2.18 Change Flow Control 32
- 2.19 Change Forward Switch 33
- 2.20 Change Gateway 33
- 2.21 Change Inactive Logout 34
- 2.22 Change Inactive Timer 34
- 2.23 Change Incoming 35
- 2.24 Change IPAddress 36
- 2.25 Change IPSecurity 36
- 2.26 Change LAT CircTimer 37
- 2.27 Change LAT Groups 38
- 2.29 Change Loadhost 38
- 2.30 Change Local Switch 39
- 2.31 Change Loginpass 40
- 2.32 Change Modem Control 40
- 2.33 Change Modem Emulation 41
- 2.34 Change Name 41
- 2.35 Change Nameserver 42
- CHANGE NETWARE LOADHOST 43
- 2.39 Change NetWare Routing 44
- 2.40 Change Parity 44
- 2.41 Change Passflow 45
- 2.43 Change Password Limit 46
- 2.45 Change Portname 47
- 2.46 Change Preferred 48
- 2.47 Change Privpass 49
- 2.48 Change RARP 49
- 2.50 Change Rlogin 50
- 2.51 Change RS485 51
- 2.52 Change Secondary 52
- 2.53 Change Session Limit 52
- 2.54 Change Signal Check 52
- 2.55 Change Silentboot 53
- 2.56 Change SNMPSetComm 53
- 2.57 Change Software 54
- 2.58 Change Speed 54
- 2.59 Change Startup 55
- 2.60 Change Stopbits 56
- 2.61 Change Subnet Mask 56
- 2.62 Change TCPKeepalive 57
- 2.63 Change Telnetdest 57
- 2.64 Change Telnetpad 58
- 2.65 Change Termtype 58
- 2.66 Change Timeserver 59
- 2.67 Change Verify 60
- 2.68 Change WINS 60
- 2.69 Crypt Password 61
- 2.70 Disk 62
- 2.71 Delete IPSecurity 66
- 2.72 Disconnect 66
- 2.73 Finger 66
- 2.74 Forward 67
- 2.75 Help 67
- 2.76 Hostlist 67
- 2.77 Initialize 68
- 2.78 LAT 69
- 2.79 Logout Port 69
- 2.80 Netstat 70
- 2.81 Ping 70
- 2.82 Resume 70
- 2.83 Rlogin 71
- 2.84 RTC 71
- 2.85 Set Privileged 72
- 2.86 Show 80211 72
- 2.87 Show Hostlist 73
- 2.88 Show IPsecurity 73
- 2.89 Show NetWare 73
- 2.90 Show Nodes 73
- 2.93 Show Server 74
- 2.91 Show Ports 74
- 2.92 Show RS485 74
- 2.94 Show Services 75
- 2.95 Show Session 75
- 2.96 Show SNMP 76
- 2.97 Show Users 76
- 2.98 Show Version 76
- 2.99 Source 76
- 2.100 SPX 77
- 2.101 Telnet 77
- 2.102 Test 78
- 2.103 Zero 78
- A: Contact Information 79
- B: Environment Strings 80
- B.2.1 Usage Examples 81
- 2.2.1.11 Y 83
- 2.2.1.12 LD=port# 83
- 2.2.1.13 LN=node# 83
- B: Show 802.11 Errors 84
- B.2.2 Rightmost Number 86
- 00000004 Internal error 88
- 00000002 Internal error 88
- 00000001 Internal error 88
Powiązane produkty i podręczniki dla Networking Lantronix MSS
(18 strony)De'Longhi TRV0715T manuály
Uživatelské manuály a uživatelské příručky pro Faxy De'Longhi TRV0715T.
Poskytujeme 1 manuály pdf De'Longhi TRV0715T ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentarze do niniejszej Instrukcji