Lantronix UDS10 Instrukcja Użytkownika Strona 38
- Strona / 78
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Configuring the UDS Using Telnet or the Serial Port UDS10/UDS100 User Guide
38
Factory Default Settings
Select 7 to reset the unit’s serial port to the factory default settings. The server
configurations (IP address information) remain unchanged. The specific settings that
this option changes are in the following list:
Channel 1 Configuration Defaults
Baudrate 9600
I/F Mode 4C (1 stop bit, no parity, 8 bit, RS-232C)
Own TCP port number 10001
Connect Mode C0 (always accept incoming connection; no active
connection startup)
Hostlist retry counter 3
Hostlist retry timeout 250 (msec)
Start character 0x0D (CR)
All other settings 0
Expert Settings Defaults
TCP keepalive 45 (seconds)
ARP cache timeout 600 (seconds)
Security Settings Defaults
SNMP Enabled
SNMP community name public
Telnet setup Enabled
TFTP download Enabled
Port 77FEh Enabled
Web Server Enabled
ECHO Disabled
Encryption Disabled
Enhanced password Disabled
Exit Configuration Mode
To exit Setup Mode:
To save all changes and reboot, select 9. All values are stored in nonvolatile
memory.
To exit the configuration mode without saving changes or rebooting, select 8.
- User Guide 1
- Copyright & Trademark 2
- Contacts 2
- Disclaimer & Revisions 3
- Contents 4
- 6: Updating Firmware 39 5
- 7: Using Monitor Mode 43 5
- Figures 6
- Purpose and Audience 8
- Chapter Summary 8
- Additional Documentation 9
- Applications 10
- Application Examples 10
- Protocol Support 12
- Additional Features 12
- Configuration Methods 12
- Product Information Label 13
- Installing the UDS 14
- Required Information 15
- DeviceInstaller 16
- Serial Port Login 17
- Accessing Web Manager 18
- Using Web Manager 20
- Using a Telnet Connection 22
- Using the Serial Port 23
- IP Address 24
- Set Gateway IP Address 24
- Netmask 24
- DHCP Naming 25
- Baudrate 26
- I/F (Interface) Mode 26
- Port Number 27
- Connect Mode 28
- Manual Connection 29
- Figure 5-6. Hostlist Option 30
- Remote IP Address 32
- Remote Port 32
- Disconnect Mode 33
- Flush Mode 33
- Pack Control 34
- Expert Settings 35
- Security Settings 36
- Factory Default Settings 38
- Exit Configuration Mode 38
- Obtaining Firmware 39
- Reloading Firmware 39
- Using TFTP 40
- Using Another Unit 41
- *** NodeSet 2.0 *** 42
- 0>DL 42
- 02049 lines loaded 42
- Using Monitor Mode Commands 44
- Collisions 45
- Diagnostics (red) 45
- Status (yellow) 45
- Problems and Error Messages 46
- Technical Support 49
- Serial Port 51
- Serial Connector Pinouts 51
- Null-Modem Cable 53
- Network Port 53
- Ethernet Connector Pinouts 54
- AutoIP 57
- ARP and Telnet 58
- Conversion Table 59
- Scientific Calculator 60
- Connect Mode Options 61
- Disconnect Mode Options 64
- Flush Mode Options 66
- Interface Mode Options 72
- Pack Control Options 73
- Declaration of Conformity 75
- Warranty 76
Powiązane produkty i podręczniki dla Networking Lantronix UDS10
(98 strony)De'Longhi TRV0715T manuály
Uživatelské manuály a uživatelské příručky pro Faxy De'Longhi TRV0715T.
Poskytujeme 1 manuály pdf De'Longhi TRV0715T ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentarze do niniejszej Instrukcji