Lantronix XPress-DR-IAP Podręcznik Użytkownika Strona 67
- Strona / 149
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Configure
3.6.6 Remote IP Address
This is the destination IP address used with an outgoing connection.
3.6.7 Remote Port
The remote TCP port number must be set for the unit to make outgoing connections. This
parameter defines the port number on the target host to which a connection is attempted.
Note: To connect an ASCII terminal to a host using the unit for login purposes, use the
remote port number 23 (Internet standard port number for Telnet services).
3.6.8 DisConnMode
DTR is hardwired to +12VDC. The Disconnect with DTR drop option is inactive.
Note: See Table 39 - Binary to Hexadecimal Conversion Table.
Table 16 - Disconnect Mode Options
Disconnect Mode Option 7 6 5 4 3 2 1 0
Disconnect with DTR drop
(6)
1
Ignore DTR 0
Telnet mode and terminal
type setup
(1)
1
Channel (port) password
(2)
1
Hard disconnect
(3)
0
Disable hard disconnect 1
State LED off with connection
(4)
1
Disconnect with EOT (^D)
(5)
1
1. The XPress DR will send the "Terminal Type" upon an outgoing connection.
2. A password is required for a connection to the serial port from the network.
3. The TCP connection will close even if the remote site does not acknowledge the disconnection.
4. When there is a network connection to or from the serial port, the state LED will turn off instead of blink.
5. When Ctrl D or Hex 04 are detected, the connection is dropped. Both Telnet mode and Disconnect with EOT must be enabled
for Disconnect with EOT to function properly. Ctrl D will only be detected going from the serial port to the network.
6. DTR hardwired to +12VDC. This option is disabled in the DSTni-XPress DR.
DSTni-XPress DR User Guide 3-21
- DSTni-XPress DR 1
- User Guide 1
- Copyright and Trademark 3
- Disclaimer and Revisions 4
- Declaration of Conformity 5
- Warranty 6
- Sales Offices 7
- Contents 10
- List of Figures 12
- List of Tables 13
- 1.1 DSTni-XPress DR 15
- Introduction 16
- PLC's XPress DR-IAP 17
- 1.4 Serial Interface 19
- 1.5 RJ-45 Serial Connector 20
- 1.7 RJ-45 Ethernet Interface 22
- 1.9 Front Panel Description 25
- 1.10 LEDs 27
- 1.11 Dimensions 28
- 1.13 Power Requirements 29
- 1.14 Reset Switch 29
- 1.15 RS-232/RS-485 Switch 30
- Table 7 - Technical Specs 31
- Getting Started 33
- 2.1.3 Port Number 34
- 2.3.1 DHCP 37
- 2.3.2 AutoIP 37
- 2.4 DeviceInstaller 38
- 2.4.3 Test the IP Address 40
- 2.5 ARP and Telnet 44
- 2.6 Serial Port Login 45
- Configure 47
- 3.2 Using DeviceInstaller 48
- 3.3 Web Manager Page 50
- 3.3.1 Unit Configuration 51
- 3.3.2 Server Properties 52
- 3.3.3 Port Properties 53
- 3.3.4 Update Settings 55
- 3.3.5 Technical Support 55
- 3.4.2 Using the Serial Port 58
- 3.5.1 IP Address 58
- 3.5.5 DHCP Naming 60
- 3.6.1 Baudrate 61
- 3.6.2 I/F (Interface) Mode 61
- 3.6.3 Flow 62
- 3.6.4 Port Number 63
- 3.6.5 Connect Mode 64
- 3.6.6 Remote IP Address 67
- 3.6.7 Remote Port 67
- 3.6.8 DisConnMode 67
- 3.6.10 Pack Control 69
- 3.6.12 Send Characters 70
- 3.6.13 Telnet Terminal Type 70
- 3.7 Expert Settings 71
- 3.8 Security Settings 71
- 3.9 Factory Defaults 73
- 3.11 Get Configuration 73
- 3.12 Set Configuration 74
- 4.1 Protocol Firmware 75
- 4.2.1 Via DeviceInstaller 76
- Firmware 77
- 4.2.2 Via TFTP 79
- 4.2.3 Via Another Unit 79
- 4.2.4 Via the Serial Port 80
- 5.1 Overview 81
- Comm Port Redirector 82
- 5.3 Using Redirector 83
- 5.3.1 Port Setup 84
- 5.3.2 Comm App Setup 84
- 5.3.5 Port Settings 86
- 5.3.6 Listen Mode 86
- 5.3.7 Silent Mode 87
- 5.3.8 TCP Keepalive 87
- 6.1 Technical Support 89
- Troubleshooting 90
- 7.1 Monitor Mode 95
- 0> OK; no error 96
- 8> Wrong parameter(s) 96
- 9> Invalid command 96
- 8.1 UDP Datagrams 97
- 8.2.2 Sending a Setup Record 100
- 8.2.3 The Intel Hex Format 101
- 0300300002337A1E 102
- 8.3 Setup Records 103
- 8.3.1 Channel Parameters 104
- 8.3.2 Interface Mode 105
- 8.3.3 Baud Rate 106
- 8.3.4 Flow Control 106
- 8.3.5 Connect Mode 107
- 8.3.6 Disconnect Mode 108
- 8.3.8 Pack Control 109
- 8.4 IP Addresses 110
- 8.4.3 Host Portion 111
- 8.4.4 Network Address 111
- 8.4.5 Broadcast Address 111
- 8.4.7 Network RFCs 112
- 9.1 Connect Mode Options 114
- Binary to Hex 115
- 9.2 Disconnect Mode Options 117
- 9.4 Interface Mode Options 126
- 9.5 Pack Control Options 127
- 10.1 Class A Network 129
- 10.2 Class B Network 129
- 10.3 Class C Network 129
- 10.4 Network Address 130
- 10.5 Broadcast Address 130
- 10.6 IP Netmask 130
- 10.8 Network RFCs 131
Powiązane produkty i podręczniki dla Serwery szeregowe Lantronix XPress-DR-IAP
(83 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji